Completely new concept for inflating airbags

Autoliv has announced it has developed a completely new concept for inflating airbags that is more environmentally friendly and more cost efficient than traditional inflator technologies. In addition, it reduces the inflator’s weight by 20 per cent compared to most inflators for the intended application.
March 22, 2012 Read time: 2 mins
4171 Autoliv has announced it has developed a completely new concept for inflating airbags that is more environmentally friendly and more cost efficient than traditional inflator technologies. In addition, it reduces the inflator’s weight by 20 per cent compared to most inflators for the intended application.

The new inflator went into production earlier this year, in a passenger-side airbag for a European manufacturer of premium-brand vehicles. It uses hydrogen and oxygen with inert gas to inflate the airbag, instead of pyro­technic substances. As a result, there are no waste particles at all from the combustion and no effluent gases, not even carbon dioxide. The only side product is regular vapour which, when cooled off, becomes just a few drops of pure water, making the inflator extremely environmentally friendly.

In addition, the mixing of the hydrogen and the oxygen takes place in the textile cushion of the airbag, instead of in a steel vessel as in traditional airbag inflators, which allows for a thinner and lighter steel container and reduces weight and costs.

Autoliv says the weight reduction depends on the original inflator but is approximately 20% compared to most traditional inflators for airbags on the front passenger side. If only a quarter of company’s own needs for such passenger airbag inflators were converted to the new hydrogen/oxygen technology, Autoliv says it would save 1,000 tons of steel every year. Additionally, the vehicles with the new inflator would reduce their fuel consumption by more than eight million litres over the expected life time of the vehicles.

The new APG hydrogen/oxygen inflator will primarily be used in frontal airbags for the front-passenger side where higher gas quantities are required than for other airbags in a vehicle. The next step for this technology is to develop a dual-stage version of the inflator to be able to adjust the gas flow to the severity of the crash and to other parameters. Autoliv says this will be done using two independent ignitors and varying the time lapse a few milliseconds between the ignitions.

For more information on companies in this article

Related Content

  • Zero-emission bus project saves fuel
    December 22, 2015
    The CHIC (Clean Hydrogen in European Cities) project, a zero-emission bus project, has saved over four million litres of fuel since it began, according to the project’s coordinators. As part of the project 56 fuel cell buses – emitting nothing but water-vapour - have been operating in eight cities: Aarau (Switzerland), Bozen (Italy), London (UK), Milan (Italy) and Oslo (Norway), Cologne and Hamburg (Germany) and Whistler (Canada).
    Read More
  • New UK study trials effectiveness of low-emission HGVs
    July 25, 2017
    Cenex, the UK’s Centre of Excellence for low carbon technologies is to partner with logistics provider Kuehne + Nagel to trial the effectiveness of low-emissions heavy-goods vehicles (HGVs) operating as parts of large fleets with demanding-duty cycles. Funded in part by Innovate UK’s Low-Emission Freight and Logistics Project, the Reduced-Emission Logistics (RED-E-LOG) trial will see one of the UK’s largest fleet operators trial the effectiveness of dedicated (spark-ignited) gas and dual-fuel direct injecti
    Read More
  • Wireless traffic management reduces costs and commute times
    January 30, 2012
    The County of Los Angeles is widely known for having among the worst traffic problems and the most road congestion in the US. To combat these problems, the Los Angeles County Department of Public Works decided to deploy a wireless communications system to connect over 1,000 of the most congested intersections so they could dynamically monitor and manage the congestion and reduce commute times.
    Read More
  • The cost benefits of LED traffic signals
    July 16, 2012
    On 11 January 2005, the Kentucky Transportation Cabinet (KYTC) began installing GELcore LED traffic signal modules state-wide through an Energy Savings Performance Contract. In tendering for the work, the energy service contractors could choose any manufacturers equipment but all of them proposed to use the GELcore brand.
    Read More

Highlighted Content