Skip to main content

What happens to an electric car in a frontal crash?

At the Detroit Auto Show 2011, Volvo Cars is spotlighting the important issue of electric car safety in an unusual, but distinctive way. On the company's stand there is a Volvo C30 Electric that has undergone a frontal collision test at 40 mph (64 km/h).
January 26, 2012 Read time: 3 mins

At the Detroit Auto Show 2011, 609 Volvo Cars is spotlighting the important issue of electric car safety in an unusual, but distinctive way. On the company's stand there is a Volvo C30 Electric that has undergone a frontal collision test at 40 mph (64 km/h).

"Our tests show it is vital to separate the batteries from the electric car's crumple zones to make it as safe as a conventional car. In Detroit we are the first car maker to show the world what a truly safe electric car looks like after a collision with high-speed impact," says Volvo Cars' president and CEO Stefan Jacoby.

The car on show had a fully charged battery when it was tested at Volvo Cars' crash test laboratory in early December 2010. The crash was a so-called offset collision in which 40 per cent of the front hit a barrier at 40 mph (64 km/h).

"The test produced exactly the results we expected. The C30 Electric offers the very same high safety level as a C30 with a combustion engine. The front deformed and distributed the crash energy as we expected. Both the batteries and the cables that are part of the electric system remained entirely intact after the collision," relates Jan Ivarsson, senior manager Safety Strategy & Requirements at Volvo Cars.

The structure of an electric car differs considerably from that of a conventional car - and the new components pose a number of fresh safety challenges. In order to give the Volvo C30 Electric a range of up to 95 miles (150 km) it is necessary to have a battery pack that weighs about 660 lb (300 kg) and this takes up far more space than a conventional fuel tank. Under the bonnet, the combustion engine has been replaced by a more packaging-efficient and lighter electric motor. What is more, the car has a 400 Volt high-voltage electric system.

"Our far-reaching research emphasises the importance of separating the lithium-ion batteries from the car's crumple zones and the passenger compartment. This is the same safety approach we apply with regard to the fuel tank in a conventional car. Another challenge is to reinforce the crumple zones at the front where the smaller motor occupies less space than usual," says Ivarsson.

In the Volvo C30 Electric the batteries are fitted in the traditional fuel tank position and in the tunnel area. The batteries are robustly encapsulated. Beams and other parts of the car's structure around the battery pack are reinforced. All the cables are shielded for maximum protection.

The crash sensor in the car also controls the fuses - and power is cut in 50 milliseconds in a collision by the same signal that deploys the airbags. The system has several fuses that cut directly if an earth fault is detected, such as a damaged cable coming into contact with the body frame.

In a conventional car, the combustion engine helps distribute the incoming collision forces. In the C30 Electric this task is performed by a reinforced frontal structure that also helps absorb the increased collision energy created as a result of the car's added weight.

For more information on companies in this article

Related Content

  • Electric vehicles in construction are the future, say researchers
    December 20, 2016
    The industrial and commercial sector is the largest part of the electric vehicle value market and that will continue to be the case according to analysis in the IDTechEx report, Industrial and Commercial Electric Vehicles 2017-2027. Buses are the largest part of that and they are mainly made in China for China, where typical orders are ten times the size of orders elsewhere. Less dramatically, construction, mining and agriculture do not see 70 per cent grants for EV versions yet they are steadily becomin
  • Industry AMS cushions the blow for crashing motorists
    April 5, 2016
    Those with an interest in crash attenuation should make their way to the Industry AMS stand in Hall 4 where the company is showing some new additions to its range, including work zone and motorcycle-friendly solutions. Many of the company’s products use a collapsible, energy-absorbing honeycomb and a variation of this is used in a new moveable barrier end for temporary concrete barriers used to separate live lanes from work zones. The portable version is mounted on a very heavy cast iron base enabling it t
  • ‘What’s the optimum number of cooks?’ asks Valerann
    October 23, 2023
    ITS Software as a Service specialist explains in detail how cross-source, cross-type, deep data fusion is solving global traffic accident conundrums
  • Average speed cameras reduce injury collisions, says report
    October 31, 2016
    Research carried out into average speed camera (ASC) effectiveness by the UK’s RAC Foundation concludes that the implementation of ASCs in the locations that have been assessed in its report has had the effect of reducing injury collisions, and especially those of a higher severity. Even taking into account other influencing factors, the report says the reductions are large and statistically significant. Researchers analysed detailed accident data taken from 25 sites where average speed cameras were inst