Completely new concept for inflating airbags

Autoliv has announced it has developed a completely new concept for inflating airbags that is more environmentally friendly and more cost efficient than traditional inflator technologies. In addition, it reduces the inflator’s weight by 20 per cent compared to most inflators for the intended application.
March 22, 2012 Read time: 2 mins
4171 Autoliv has announced it has developed a completely new concept for inflating airbags that is more environmentally friendly and more cost efficient than traditional inflator technologies. In addition, it reduces the inflator’s weight by 20 per cent compared to most inflators for the intended application.

The new inflator went into production earlier this year, in a passenger-side airbag for a European manufacturer of premium-brand vehicles. It uses hydrogen and oxygen with inert gas to inflate the airbag, instead of pyro­technic substances. As a result, there are no waste particles at all from the combustion and no effluent gases, not even carbon dioxide. The only side product is regular vapour which, when cooled off, becomes just a few drops of pure water, making the inflator extremely environmentally friendly.

In addition, the mixing of the hydrogen and the oxygen takes place in the textile cushion of the airbag, instead of in a steel vessel as in traditional airbag inflators, which allows for a thinner and lighter steel container and reduces weight and costs.

Autoliv says the weight reduction depends on the original inflator but is approximately 20% compared to most traditional inflators for airbags on the front passenger side. If only a quarter of company’s own needs for such passenger airbag inflators were converted to the new hydrogen/oxygen technology, Autoliv says it would save 1,000 tons of steel every year. Additionally, the vehicles with the new inflator would reduce their fuel consumption by more than eight million litres over the expected life time of the vehicles.

The new APG hydrogen/oxygen inflator will primarily be used in frontal airbags for the front-passenger side where higher gas quantities are required than for other airbags in a vehicle. The next step for this technology is to develop a dual-stage version of the inflator to be able to adjust the gas flow to the severity of the crash and to other parameters. Autoliv says this will be done using two independent ignitors and varying the time lapse a few milliseconds between the ignitions.

For more information on companies in this article

Related Content

  • On a WIM – a global view of weigh in motion
    May 25, 2016
    Q-Free’s Andrew Lees looks at regional characteristics and technology trends in the global Weigh-In-Motion market. The principles of Weigh-In-Motion (WIM) are well established. Data derived from vehicles passing over in-ground sensors can be interpreted for vehicle classification (axle counts and spacing) and positive identification (especially when linked to image capture) applications as well as to derive individual axle and gross vehicle weight (GVW).
    Read More
  • Workzone safety can be economically viable
    October 24, 2014
    David Crawford looks how workzone safety can be ‘economically viable’. Highway maintenance is one of the most dangerous construction industry occupations in Europe. Research from The Netherlands on fatal crashes indicates that the risk facing road workzone operatives is ‘significantly higher’ than that for the general construction workforce. A survey carried out by the Highways Agency, which runs the UK’s motorway and trunk road network, has suggested that 20% of road workers have suffered injuries from pa
    Read More
  • Monitoring, detection and control systems inside tunnels can do much to improve traveller safety
    August 6, 2013
    ITS technology can do a great deal to improve tunnel safety, as Colin Sowman discovers. It was back in April 2004 that the European Parliament adopted the EU Directive which lays down the Minimum Safety Requirements for Tunnels in the Trans-European Road Network (2004/54/EC). This was the first unitary legislation setting minimum safety standards for European road tunnels and was designed to harmonise the management of tunnel safety at a national level. Operators of existing tunnels have until 30 April 201
    Read More
  • Deadlines approach for Europe’s automatic crash alert system
    September 15, 2016
    The EU-co-funded I_ HeERO (Infrastructure_ Harmonised eCall European Pilot) project is working to ensure the readiness of national networks of call centres - known as public safety answering posts (PSAPs) - to deal with automated crash alerts arriving via the continent-wide 112 emergency phone number. Following on from its HeERO and HeERO2 pre-deployment predecessors, which enjoyed €16m (US$17.76m) in EU funding, the new initiative runs from 1 January 2015 to 31 December 2017. It has €30.9 million (US$34.
    Read More

Highlighted Content