Kistler installs WiM system on Czech highway

The Czech Metrology Institute (CMI) has approved a Weigh in Motion (WiM) system from Kistler to help prevent road damage from trucks. Kistler, a measurement technology company, says its KiTraffic system is being used to track and fine overloaded trucks on the D7 Highway from Prague to the north-west of the country. KiTraffic is comprised of Lineas brand quartz sensors integrated into the road, cameras, hardware and software. If a truck exceeds the weight limit, the system sends the weight and a photograph
September 23, 2019 Read time: 2 mins

The Czech Metrology Institute (CMI) has approved a Weigh in Motion (WiM) system from 657 Kistler to help prevent road damage from trucks.

Kistler, a measurement technology company, says its KiTraffic system is being used to track and fine overloaded trucks on the D7 Highway from Prague to the north-west of the country.

KiTraffic is comprised of Lineas brand quartz sensors integrated into the road, cameras, hardware and software. If a truck exceeds the weight limit, the system sends the weight and a photograph of the vehicle to the authorities who can then send a standard letter to fine the owner, the company adds.

It was installed in collaboration with system integrator Spel on a new section of the highway. As part of an accuracy test, the team weighed vehicles from categories B (a 994 Volkswagen transporter), C (a six-axle truck) and D (a bus) on stationary scales and then in motion via the WiM system. Kistler passed CMI’s maximum error margin of 5% per vehicle and 11% per axle.

Tomas Pospisek, global market development manager for road & traffic EMEA at Kistler, says: “This error margin is factored in by the system to make sure no vehicle is fined incorrectly.”

The WiM system was certified by the International Organisation of Legal Metrology (OIML) and the Swiss Federal Institute for Metrology.

“There is currently no pan-European certificate for WiM systems. However, having already obtained a more general measuring certificate, the OIML helped us to get approved in the Czech Republic,” Pospisek continues. “This meant we were able to skip some tests and save time.”

Looking ahead, Kistler is hoping to open 15 WiM stations on Czech highways.

Urban Traffic Control

For more information on companies in this article

Related Content

  • Dual purpose for new weigh-in-motion site
    October 13, 2014
    A new weigh-in-motion weighbridge is being installed on State Highway 1 at the Rakaia Bridge to support the introduction of high productivity motor vehicles (HPMV) on this key South Island, New Zealand, freight route. The HPMV system allows vehicles carrying a divisible load of essential goods to weigh more than the official 44 metric tonnes without a permit, but only on specified routes.
    Read More
  • Design improvements for better truck safety delayed till 2022
    March 11, 2015
    On 10 March, the European Parliament approved amendments to the directive on the maximum authorised dimensions and weights for trucks and buses. The final agreement allows for much needed design adaptations to make cabs safer, but only following a revision by the European Commission of the cab type-approval. This means that manufacturers will not be required to implement these changes until 2022. It further retains each Member State’s right to decide whether or not they want to allow the use of mega trucks
    Read More
  • C-ITS in the EU: ‘A little tribal’
    April 1, 2019
    As the C-ITS Delegated Act begins its journey through the European policy maze, Adam Hill looks at who is expecting what from this proposed framework for connected vehicles – and why some people are insisting that the lawmakers are already getting things wrong here are furrowed brows in Brussels and Strasbourg as European Union legislators begin to consider the rules which will underpin future services such as connected vehicles. The idea is to create a regulatory framework to harmonise cooperative ITS
    Read More
  • C-ITS in the EU: ‘A little tribal’
    April 1, 2019
    As the C-ITS Delegated Act begins its journey through the European policy maze, Adam Hill looks at who is expecting what from this proposed framework for connected vehicles – and why some people are insisting that the lawmakers are already getting things wrong here are furrowed brows in Brussels and Strasbourg as European Union legislators begin to consider the rules which will underpin future services such as connected vehicles. The idea is to create a regulatory framework to harmonise cooperative ITS
    Read More

Highlighted Content