Kistler installs WiM system on Czech highway

The Czech Metrology Institute (CMI) has approved a Weigh in Motion (WiM) system from Kistler to help prevent road damage from trucks. Kistler, a measurement technology company, says its KiTraffic system is being used to track and fine overloaded trucks on the D7 Highway from Prague to the north-west of the country. KiTraffic is comprised of Lineas brand quartz sensors integrated into the road, cameras, hardware and software. If a truck exceeds the weight limit, the system sends the weight and a photograph
September 23, 2019 Read time: 2 mins

The Czech Metrology Institute (CMI) has approved a Weigh in Motion (WiM) system from 657 Kistler to help prevent road damage from trucks.

Kistler, a measurement technology company, says its KiTraffic system is being used to track and fine overloaded trucks on the D7 Highway from Prague to the north-west of the country.

KiTraffic is comprised of Lineas brand quartz sensors integrated into the road, cameras, hardware and software. If a truck exceeds the weight limit, the system sends the weight and a photograph of the vehicle to the authorities who can then send a standard letter to fine the owner, the company adds.

It was installed in collaboration with system integrator Spel on a new section of the highway. As part of an accuracy test, the team weighed vehicles from categories B (a 994 Volkswagen transporter), C (a six-axle truck) and D (a bus) on stationary scales and then in motion via the WiM system. Kistler passed CMI’s maximum error margin of 5% per vehicle and 11% per axle.

Tomas Pospisek, global market development manager for road & traffic EMEA at Kistler, says: “This error margin is factored in by the system to make sure no vehicle is fined incorrectly.”

The WiM system was certified by the International Organisation of Legal Metrology (OIML) and the Swiss Federal Institute for Metrology.

“There is currently no pan-European certificate for WiM systems. However, having already obtained a more general measuring certificate, the OIML helped us to get approved in the Czech Republic,” Pospisek continues. “This meant we were able to skip some tests and save time.”

Looking ahead, Kistler is hoping to open 15 WiM stations on Czech highways.

Urban Traffic Control

For more information on companies in this article

Related Content

  • IRD demonstrates SAW III portable axle scale
    April 5, 2016
    International Road Dynamics is demonstrating its new SAW III portable axle scale and VectorSense sensor technology here at Intertraffic Amsterdam. The SAW III scale is certified for enforcement weighing of transport trucks and can also be used for screening vehicles at slow speed using weigh-in-motion (WIM).
    Read More
  • IRD complements WIM with tyre under-inflation detection
    May 8, 2015
    To complement its existing WIM offering, IRD has introduced a system to detect under-inflated and flat tyres at highway speeds. Tyre inflation pressure has both safety and economic impacts for road users and none more so than with commercial vehicles. An underinflated tyre has decreased directional control, increased risk of catastrophic failure, and negatively impacts tyre life and fuel economy. In June 2014 the USDOT published Large Truck and Bus Crash Facts 2012 in which the Federal Motor Carrier Safety
    Read More
  • Intercomp launches LS-WiM system for fleet operators
    April 17, 2019
    Intercomp has launched a low-speed Weigh in Motion (LS-WiM) system which it says allows fleet managers to collect the weight of vehicles without hampering traffic flow. The system is suitable for high-volume entry and exit gates and, unlike full-length truck scales, does not require incoming and outgoing traffic to stop every time a vehicle needs to be weighed, the company adds. According to Intercomp, the system’s small footprint allows it to be installed at most facilities at approximately half
    Read More
  • IRD to install WIM sorting system in South Dakota
    January 2, 2019
    International Road Dynamics (IRD) is to install its Weigh-in-Motion (WIM) sorting system to protect road infrastructure in the US state of South Dakota. The $1.3 million deal is part of a wider ambition from the South Dakota Department of Transportation to deploy more WIM systems throughout the state. The Port of Entry Commercial Vehicle WIM Sorting System is scheduled to be operational by December 2019 at the Valley Springs Port of Entry on Interstate 90 east of Sioux Falls. It is expected to weigh all
    Read More

Highlighted Content