IRD customised weight enforcement system goes live in Spokane

International Road Dynamics (IRD) has been working with the Washington State Patrol (WSP) and the Washington State Department of Transportation (WSDOT) to support delivery of a customised weight enforcement and commercial vehicle inspection solution which integrates vehicle identification, credential screening and data collection for the Spokane Port-of-Entry (POE) Weigh Station on I-90. Yesterday, the station’s grand opening was held at the POE which is located on Interstate 90 one mile west of the Washing
June 14, 2012 Read time: 2 mins
69 International Road Dynamics (IRD) has been working with the Washington State Patrol (WSP) and the 451 Washington State Department of Transportation (WSDOT) to support delivery of a customised weight enforcement and commercial vehicle inspection solution which integrates vehicle identification, credential screening and data collection for the Spokane Port-of-Entry (POE) Weigh Station on I-90. Yesterday, the station’s grand opening was held at the POE which is located on Interstate 90 one mile west of the Washington/Idaho border.

IRD supplied and integrated its world-leading Single Load Cell and IRD-PAT Bending Plate weigh-in-motion (WIM) scales, AVI (automatic vehicle identification), tracking sensors, over-height detection, variable message signs (VMS), changeable message signs (CMS), side view enforcement cameras, and automatic licence plate readers (ALPR) with optical character recognition (OCR). All of the equipment is interfaced with IRD’s state-of-the-art iSinc controller electronics. The system provides WIM vehicle data that is used for the Washington State DOT Commercial Vehicle Information Systems and Networks (CVISN). This is the 12th weight enforcement site in Washington for which IRD has supplied components and systems.

“This technology gives our commercial vehicle enforcement officers the ability to focus on companies who try and dodge the rules and not maintain their trucks,” said Washington State Patrol Chief John R. Batiste. “Companies with solid track records of compliance will be allowed to continue on their way, with very little delay.”  

As Terry Bergan, IRD’s president and CEO points out, at busy times, weigh stations are often overloaded and are forced to close while a back-log of trucks is cleared. “By combining vehicle weight and dimensions, as measured by IRD’s weigh-in-motion (WIM) systems, in conjunction with credential information such as the Washington State DOT CVISN data, the weigh station can focus on high risk vehicles, allowing carriers with good safety records and weight compliant trucks to bypass the weigh station. Not only does this greatly improve the operation of the weigh station, but it is of considerable benefit to the trucking industry, reducing wait times at weigh stations for reputable and cutting fuel bills and emissions in the process,” Bergan said.
Classification & Data Collection

For more information on companies in this article

Related Content

  • Vehicle identification systems aid dynamic bus operations
    April 24, 2013
    David Crawford looks at a global trend towards more efficiency in less space As buses gain increased profile in the public transport mix needed for modal shift, attention is turning towards improving terminal layouts for more efficient handling of services and passengers. Locations, too, tend to be in central areas of cities, where sites are restricted and land values high. Enter the dynamic bus station, which uses modern vehicle identification systems to optimise space use and streamline service operation
    Read More
  • Traffic Data Systems receives Swiss certification for WIM system
    September 19, 2017
    Traffic Data Systems’ WIM-DSP 32 low-speed and high-speed weigh-in-motion (WIM) system has been awarded an OIML-R134-1 certificate by the Swiss Federal Institute of Metrology, proving accuracy levels of ±5% (initial verification) and ±10% (in-service inspection) have been achieved. The Swiss institute’s supervised certification process required more than 500 test runs with different vehicles, speeds and loads.
    Read More
  • Texas, Oklahoma move to interoperable tolling
    April 25, 2013
    Electronic toll systems in Texas and Oklahoma could be interoperable as soon as 2014, according to toll authorities from both states. Moves to link tolling systems in Texas and Oklahoma will enable drivers with Texas tolling accounts or Oklahoma turnpike accounts to travel on the other state’s toll roads using their current toll tags. The tolls would be automatically billed to the out-of-state driver’s account. “Oklahoma Governor Mary Fallin said it would be good to have interoperability with other states,
    Read More
  • CAMEA WIM is type approved and turnkey for weigh-in-motion
    October 23, 2012
    CAMEA WIM, developed and manufactured by CAMEA image and signal processing, is a turnkey solution for weigh-in-motion applications, from traffic reports to enforcement. According to CAMEA, the high speed system allows vehicles thought to be overloaded to be pre-selected and directed to a precise weigh station without impact on traffic flow. The CAMEA WIM – type approved for weight enforcement in the Czech Republic – also provides rich sets of traffic data in database format for export in standard formats.
    Read More

Highlighted Content