Skip to main content

Study shows road markings deliver cost-effective road safety

Road markings are among the most cost-effective solutions to make roads safer. A recent study carried out for the American Glass Bead Manufacturer’s Association quantifies by just how much Despite only making up 23% of the US mileage, fatalities on America’s rural two-lane highways made up 57% of all traffic fatalities in 2009 — resulting in more than $77Bn in losses for that year alone. Moreover, a rural motorist is 2.7 times more likely to be involved in a fatal crash per mile travelled than their urban
June 20, 2012 Read time: 4 mins
Jon Sproul, general manager of Swarco Industries

Road markings are among the most cost-effective solutions to make  roads safer. A recent study carried out for the American Glass Bead  Manufacturer’s Association quantifies by just how much

Despite only making up 23% of the US mileage, fatalities on America’s rural two-lane highways made up 57% of all traffic fatalities in 2009 — resulting in more than $77Bn in losses for that year alone. Moreover, a rural motorist is 2.7 times more likely to be involved in a fatal crash per mile travelled than their urban counterpart.

The TTI study, entitled An Evaluation of the Effectiveness of Wider Edge Line Pavement Markings, shows that, just by using six inch (15.25cm) line marking, instead of the still widely used four inch edge line, there is a dramatic improvement in safety and reduction of fatalities on rural two-lane highways.
In its recommendations, the TTI study says, “Agencies can use the results herein to develop a policy for six inch edge lines on their rural, two lane highways. Wider edge lines have been shown to reduce total crashes 15-30%, and fatal plus injury crashes 15-38%.

Comparative Benefit-Cost Ratios by Policy
Wider Edge Lines  
 $32.87-$55.20
 for every $1.00 invested
 Rumble Strips  $37.00-$46.00
 for every $1.00 invested
Chevrons  $8.60-$45.90
 for every $1.00 invested
RRPMs 
 $13.16    
 for every $1.00 invested

The study also looked at other road marking systems and assessed their safety and cost benefits, including rumble strips, chevrons, and raised retroreflective markers

In addition, the benefit-cost ratio for wide edge lines is $33 to $55 for each $1 spent, which is similar to rumble strips. If an agency is considering installing rumble strips as a safety countermeasure but concerned about the potential noise or pushback from the bicycle community, wider edge lines appear to offer similar results but without the concerns often associated with shoulder rumble strips.”

Many states have adopted wider edge lines on a variety of roads for a variety of reasons. The adoption has been slow and uncoordinated, without sound empirical findings to support their policy choice. The recent analysis of data from three states provides the necessary evidence to support the adoption of wider edge lines on rural two-lane highways. Based on the results of the cost benefit analysis above, state DOTs can now have further reassurance that their actions are in the best economic interest of society as well.

Since the safety benefits of wider edge lines are now better documented with rigorous statistical analyses, TTI says it would be beneficial if the MUTCD could be amended so that the minimum edge line width on rural two-lane highways was six inches. Agencies would then be able to implement the policy in a uniform and consistent manner.

Asked to comment on the TTI report, prepared on behalf of the 5963 American Glass Bead Manufacturer’s Association (AGBMA), Jon Sproul, general manager of glass bead and road marking material manufacturer 129 Swarco Industries and a member of the association, said the TTI report is a major contribution towards improving safety on the roads.

“While previous studies always found that edge markings have a positive impact on traffic safety, no reliable statistical data was available to support the hypothesis that wider edge lines further improve traffic safety. The TTI report is based on recent statistically sound data and several surveys conducted over the past decade. The findings confirm that an increase of merely two inches in the width of edge lines will provide better guidance and visibility and hence reduce the number of crashes on rural two-lane highways,” says Sproul and emphasises that road markings still remain among the most cost-effective and reliable solutions to make roads safer.


For more information on companies in this article

Related Content

  • RedSpeed offers schools automated no-cost stop arm enforcement
    March 28, 2014
    School authorities in the US are turning to automated school bus stop arm enforcement to curb an astonishing number of violations. It is estimated that every year nearly 17,000 American children are sent to emergency rooms as a result of school bus related crashes. And when surveyed, 99% of school bus drivers reported that the most dangerous behaviour they encounter is drivers passing a school bus with its stop sign arm extended. Every day these drivers who violate the extended stop arm signs put at risk
  • MRL's Mini Mac 400 makes mark
    February 22, 2018
    Among a range of equipment that MRL will showcase at Intertraffic Amsterdam will be the Mini Mac 400, an agile, compact design machine, perfect for increasing productivity applying thermoplastic intersection and lane markings. It has an easy-fill 400lb/181kg capacity material tank with an integral material pump, 100lb/45kg glass bead capacity, adjustable width ribbon extrusion die, 25hp LP-fuelled engine, and electronic skip line timing system.
  • Cost benefit: Wichita eases workzone congestion
    July 8, 2019
    Achieving higher diversion rates has helped one Kansas city to make traffic flow more efficient around workzones. David Crawford examines what’s behind a 10:1 benefit-to-cost ratio in Wichita Around 10% of highway congestion in the US results from delays in workzones, leading to an estimated annual loss of $700 million in fuel costs alone. The lack of accessible real-time traffic information to help motorists minimise their inconvenience – particularly at peak times - is a major contributor. One solut
  • Autonomous driving – what can we really expect?
    June 6, 2016
    Dave Marples of Technolution BV looks beyond the hype to the practical implementation of autonomous vehicles. Having looked at the development of this sector for some time, I am concerned about the current state of autonomous driving development as engineering (and marketing) have run way ahead of the wider systemic, and legislative, requirements to support an autonomous future.